Displaying results 0 to several of several search results
You can view the first 3 pages (30 results). To view all
several results. You must be an Agoraquest member with over 100 posts or a Premium Member. It's free to register and to
upgrade to Premium Membership is only $12 per year. Also there are several incredible benefits with Premium Membership
including access to over 4,000 service manuals, faster post response and access to Private Messaging our top
members.
To view benefits, screenshots and how to easily upgrade to premium membership by clicking here
|
| Page Number: |
| Forum |
Topic |
Author |
Replies |
Posted |
| | | 0 | |
| First 650 characters of this post | |
| Television Troubleshooting | Bravia KDL32P5600 4 blinks | jehill | 5 | 2013-06-16 12:41 |
| First 650 characters of this post |
Welcome to Agoraquest! Unfortunately, I don\'t have access to the KDL32P5600, so I can\'t tell you what the 4 blink, pause, 4 blink, etc. error code means. |
| Television Troubleshooting | kdl-46hx800 3d tv turns off then blinks 7 times | jehill | 5 | 2013-06-11 11:22 |
| First 650 characters of this post |
Welcome to Agoraquest! For the KDL46HX800, 7 blinks, pause, 7 blinks, etc. means \"Temperature Error\" and the possible location listed is \"BAL Board\".This is the starting point for a qualified service technician. |
| Television Troubleshooting | KDL-46NX810 built-in wireless stopped working | TallPaul7 | 12 | 2013-06-06 21:58 |
| First 650 characters of this post | found the service manual free online. the diagnosis screen didn't show any past error codes. I have a feeling when I replace the wireless card it will go bad again in the future. I noticed the card didn't start to go bad until I made the TV a part of the DLNA home network. It might have a problem with sending and receiving data at the same time [ This message was edited by: TallPaul7 on 2013-06-06 22:01 ] |
| Television Troubleshooting | Sony Kv32Fs12 | jehill | 2 | 2013-06-04 12:22 |
| First 650 characters of this post |
Unfortunately, I don\'t have access to the KV32FS12 service manual, so I can\'t check the error code. |
| Television Troubleshooting | Sony Bravia KDL32N4000. | jehill | 2 | 2013-06-04 12:14 |
| First 650 characters of this post |
Unfortunately, I don\'t have access to the KDL32N4000 service manual, so I can\'t check the error code. |
| Television Troubleshooting | TV Sony KDL-40CX525 - Red Screen | xmaxmex | 3 | 2013-05-29 23:54 |
| First 650 characters of this post | Hi,My Sony's screen is Red ? see the screenshot...I went to the service screen. Here's what it says (picture):006 BACKLITE 121026021418 01and103 HOST_WDT ------ 05I don't know what the errors and numbers mean. Is there a problem with the "BACKLITE"? Where can I get this part and how much does it cost?and Thanks ! |
| Television Troubleshooting | Sony Bravia KDL-32BX310 6 blink code questions | tdlunsfo | 3 | 2013-05-27 10:33 |
| First 650 characters of this post | This TV is only 18 months old and died on me after 10 hours of use. I have tried all the reset instructions to no avail.1. What does the error code mean, the sticky suggests its a Sony Bravia Speaker Voltage issue.2. Does anyone of the Service Manual for this? I downloaded one from servicemanuals.com but the power board schematic is unreadable.3. Has anyone experienced this issue with this TV family and have suggestions on where to start troubleshooting?I have a ET degree but its been a few years since I have done component troubleshooting. I can |
| Television Troubleshooting | KDF70XBR950 Blinking Green After New Optical Block | jehill | 11 | 2013-05-23 11:21 |
| First 650 characters of this post |
Welcome to Agoraquest! Operation of the POWER/STANDBY indicator is explained on p-114 of the Operating Instructions. The explanation for the indicator flashing green is that, \"the lamp for the light source is ready to turn on\". Error messages are indicated by the indicator flashing red (indicates that set is in standby) n times, a pause, n times again, etc. If \"the lamp for the light source is ready to turn on\", that suggests that the next step is for the lamp driver (lamp power supply) to start up the lamp. You had to remove the lamp driver to |
| Television Troubleshooting | Sony KV-40XBR800, help to bring this gorgeous lady to life! | Fandangos | 7 | 2013-05-18 14:34 |
| First 650 characters of this post | I really hope someone can help me out.I have soldering experience but not so much experience with TVs. I always wanted the Ferrari of CRTs the XBR800 and I got one last week. It's the 40 inches model but I knew it was defective. The tv would power on with cold boot, this means, hooking it up at the wall socket and powering it on but would not power on if you turn off and try to turn it on again.The error was the 6 blinks of death code. So this is related to IC8002 and IC8501.So after reading a lot online I swapped the ICs from brand n |
| Television Troubleshooting | XBR55HX929 Blinking led 5 times got info from diagnostics screen | Mr_Mod | 2 | 2013-05-16 23:17 |
| First 650 characters of this post | 5 flashes for that model indicates that the TCON board is faulty.
5X Blink - TCON Error
The 5X blink protection mode indicates a communications error between the TCON Board and the X-Reality microprocessor on the Main Board. If the TCON is available for replacement, replace the
TCON. If the TCON is not available, the LCD panel must be replaced since the TCON circuit is part of the LCD panel assembly. In rare cases a loose or defective LVDS cable could also be the cause.
There is no TCON board listed as a spare part
There is no LCD panel listed as a spare part.
I wo |
| Page Number: |
