[phpBB Debug] PHP Warning: in file [ROOT]/viewtopic.php on line 35: Use of undefined constant topic - assumed 'topic' (this will throw an Error in a future version of PHP)
Agoraquest • View topic - How to Extend Sony Projector Lamp Life

        Advanced search
It is currently Wed Dec 11, 2019 12:00 am
Please Login or Register to take advantage of all of our forum benefits.

View topic - How to Extend Sony Projector Lamp Life

How to Extend Sony Projector Lamp Life

This section has the most popular questions related to Sony products like What does the TV blinking lights mean?, What is Protect error, How do I change the TV lamp bulb and more. Only administrators/moderators can post in this forum.

Moderator: jttar

by claudio » Tue Dec 30, 2008 6:43 pm

HEAT = BAD

The number one cause of lamp failure is excessive heat. Follow the instructions in the user manual for powering down the projector to ensure adequate cool-down.

Preventative TIPS

1.  Once the projector is turned on, wait at least 5 minutes before turning it off to allow the fan to properly cool the unit.  You do not need to unplug the power to the projector. I should stay in "sleep" mode (red light on) unless you see smoke or flames coming out of the TV!
2.  Don’t obstruct the air intake or exhaust vent.
Nothing should obstruct air flow to the vents.
3.  Keep the exhaust vent at least 2 feet from any object.
Do NOT hang paper near the projector.
4.  If the projector is built into a compartment, wall, ceiling, or shelf mount, the minimum distance requirement (usually at least 2 feet) listed in the user manual must be maintained
from any other object.
5.  Clean the projector’s air intake filter every 3 to 6 months, or more frequently based on the operating environment.
6.  Run the projector for two weeks and/or 20 hours shortly after your purchase. If the lamp is defective, it’ll usually fail within the first 10 hours of operation. Lamp warranties typically last just 90 to 180 days from the date of purchase, rather than the first installation.
Report any failures at anytime to Sony or from where you bought it as soon as failures occur. DO NOT WAIT!

LAMP LIFE SPECIFICATIONS

Lamp life is measured to industry standards, specifying a 2 hours on and 15 minutes off cycle.

HOW LONG WILL IT LAST?*

• Halogen bulbs: 70 hours
• Tungsten: 1,000 hours
• Metal halide (high pressure mercury): 1,000 to 2,000 hours
• Xenon short-arc: 400 to 2,400 hours, depending on type
• UHP (ultra-high performance by Philips): up to 4,000 hours
• HID (high-intensity discharge): 6,000 hours
*(normal use, estimates only)

BASIC LAMP TYPES

Halogen Lamps — These bulbs produce a warmer image onscreen. This lamp technology has been around for some time, and is found in many different types of projectors. When these lamps burn out, they do so immediately, so it’s important to have a few backups ready to go.

Metal Halide Lamps — These lamps produce a characteristically cooler image onscreen. As they age, they tend to fade slowly over time. When the image on the wall doesn’t seem to be as bright as it used to be, it’s probably time for a new bulb.

2,000 hours = 1 year.

Under normal circumstances, a lamp rated at 2,000 hours should last about a year, operating 7 hours/day, 5 days/week.

Most Sony Projector Lamps should last between 4,000 to 8,000 hours

THE DO’S AND DON’TS
FOR PROLONGED
LAMP LIFE

Do…
• Use the projector in a normal environment (avoid extreme humidity, temperature, and dust).
• Clean the air/dust filters according the user manual. Blocked filters make the lamp overheat and fail sooner. Manufacturers can test for this kind of failure, and any warranty becomes invalid. Always ensure that there’s good airflow around the projector.
• Use a cloth or gloves for handling.
• Operate in “economy mode,” if it’s available with your projector model.

Don’t…
• Switch off main power before cooling down the lamp, according to the user manual.
• Switch lamp on/off in short cycles (e.g., 5 minutes on, 5 minutes off.)
• Touch the lamp (in cold or operating condition) without gloves.
• Bump the projector when it’s operating.
• Move the projector during operation.
• Allow the projector to become overheated.
• The projector bulbs cost from $100 to $2150 so DO NOT USE the TV unless you need to AND DO NOT leave the TV/Projector bulb on when not in use


HANDLE WITH GLOVES
Deposits from fingerprints on the projector bulbs cause temperature “hot spots.” In the long term, the accompanying temperature gradient stresses the glass
of a bulb resulting in early failure.

MODULE OR NO MODULE?
The precise placement of the lamp in the module is critical to lamp life, and it is recommended that you buy the lamp pre-installed in a module.

Founder
Agoraquest
User avatar
claudio
Sony Addict
Sony Addict
 
Posts: 2419
Joined: Wed Aug 29, 2001 8:00 pm
Location: Rockville, MD

Return to Frequently Asked Questions for Sony Products